Copper fouling is generally of minor concern For numerous pistol shooters, given that It's not usually obvious like it could be for rifles. Still, just about anything that minimizes copper fouling is welcome.

Quoted: Understand that on the bottom of the case, you've got solid webbing, then the cavity partitions arrive up from there. Whilst there needs to be a slight radius in The underside from the barrel Therefore the round can slip in to the chamber, Should you be capturing better force loads, you desire no Component of the situation wall previously mentioned the online not supported (want the radus taper to stop at the online of the situation, not on the upper thinner partitions area instead). That's why common 9mm Operating force loads, the case wall is robust adequate that it not thoroughly supported situation would not lead to difficulties (Unless of course that brass is just aged and weak), but when You begin diving into +p loads, that A part of the un-supported case can Enable unfastened to trigger situation blow out.

Both of those Titegroup and CFE Pistol flow very nicely via a mechanical powder measure, dispensing fees so constant that it wasn’t necessary to use a powder trickler. The Titegroup generated really restricted normal deviation figures in our large bore handgun loads. 

Present industry greatest normal stress is founded at 21,000 psi, when utmost for +P loads is 23,000 psi. Even though most guns are rated for +P loads, it is best to examine While using the company to create certain that a presented model is rated for +P pressures. Regardless of whether a particular model is appropriate for +P loads, be specified that the correct (pound-rated) springs are mounted and so are fresh new or not worn out.

So rather than barking on +p  Functioning tension loads to achieve the speeds you need, you should go along with a slower burning powder that what you may have listed rather.   For 115's, the powder of decision is HS-6(in that melt away array) and for 124's, It really is blue dot (or in that burn off array) in its place. P.S, make sure that your barrel is entirely supporting the situation, and you've got greater the recoil spring pressure Therefore the pistol is not just beating it self to death Along with the slide nevertheless shifting far too far since the again of stroke.

Posted April four, 2018 2 several hours in the past, Joe4d reported: on the whole for non compensated pistols, on the list of speedier powders that still click here safely generates the velocity you would like at the upper conclusion of printed data will burn cleaner, use much less powder and deliver considerably less recoil than employing a reduced charge of the gradual powder.

Any inclination on what costs you guys are working with with Tightgroup and 115RN plated or jacketed 9MM loads? I am sensation like four.1-four.2 grains must be about appropriate, but it's neat the highest of your guide data, and down below the jacketed data, but the guide data provides a shorter OAL, and i am guessing that may be why the tension is larger. While that will seem sensible also due to the bullet getting a bigger diameter.

That bullet is rated for a maximum of 1850 fps, so it could be really useful from the rifle at the same time. I loaded the .44 to 2 distinctive ability levels utilizing six grains and nine grains of Titegroup. 

Sooner or later I can be undertaking load perform with Bullseye, Winchester231 and maybe One of a kind. Powder and primers are still not easy to appear by!

Quoted: I agree using this gentleman. "feel" is a nasty way to judge a load. Distinct powders and load mixtures should have a different pressure curve and I believe what a person largely "feels" is slide pace . In some instances the load might "sense" with regards to the exact same or maybe softer than some identified Protected load but sooner or later the pressure curve spikes right into a hazardous space.

Their Site doesnt checklist any load data for claimed bullet. Does any person have any recommendations on possibly load data or websites that have these kinds of details? Thanks.

By the way, the term “Parabellum” is taken through the Latin phrase Si vis pacem, para bellum, which loosely interprets into “get ready for war.”

Inspite of this being the same powder charge as above, the additional pounds presents a much more entire burn up. This load cycles perfectly in a Les Baer 1911 using an 18lb spring, has fair flash and smoke. It's not a nasty load in the least. Simply click to develop...

The Speer was printed in advance of CFE’s existence. I are already using online assets for my comparisons and that is why I went on the Hodgdon website. And that is once the confusion started... I am planning to 10mm cfe pistol load data check if I can contact Hodgdon to obtain a clarification. Wish me luck! Thanks again! Danny